Anyone know what the torque specs are for the exhaust header nuts? I used 14nm, sealed so far but couldn’t find any information on it anywhere. Getting the O2 sensor wire free from 2 frame locking zip ties inside chassis was TOUGH!
![Image]()
![Image]()
![Image]()
Upper and Lower Engine Bars mounted, exhaust removal required
- Tags
- decat exhuast full system
121 reading
-
Introducing the Motorcycle.com Podcast Listen Here
Bent Sprocket
81 - 100 of 186 Posts
Joined
·
432 Posts
Don't know about K-Speed but according to LA Fab theirs does
don't know about the sump guard
Triumph Speed/Scrambler 400 - Retro Riot Exhaust System
This Retro Race Exhaust System, handcrafted in the UK, seamlessly replaces the restrictive 400 exhaust system, unleashing the distinctive LA Fab sound. Featuring a megaphone design can with an additional decat header pipe, it enhances the single-cylinder thump. The classic look, combined with a...
lafabrication.uk
here's a picture of the header with a stock silencer (not my bike)
Joined
·
92 Posts
I have the black K-Speed one and sadly had to remove the lower engine guard to fit it because of the slightly more curved/rounded shape of the front.
I'll say also that the black paint on the pipe is rubbish and scratches or flakes of if you look at it wrong. Not at all impressed.
Joined
·
1 Posts
Hi , I’m wondering , I took my muffler off as part of taking rear wheel off to install my rally raid spoke rims. I think it looks great ,any advise on using bike with stock exhaust ,without muffler ,would be appreciated ,please people that know not just hear say ,with respect
Many thanks in advance
![Image]()
Many thanks in advance
Joined
·
48 Posts
I wouldn’t have thought that you would get away with it for long to be honest, too many NIMBY’s around !. The wheels look great but black ?. should have been gold surely ?.
Hi
I too have purchased a new AEW silencer for the 400x scrambler.
However it won't fit!
I have tried lubricating the pipe that goes to the cat.
But It won't go on!
I noticed there is a split sleeve of tube inside - which i presume is to seal the end where the bolt is - but it all seem s very tight & also close to the swinging arm.
Help appreciated on how you got yours to fit?
I too have purchased a new AEW silencer for the 400x scrambler.
However it won't fit!
I have tried lubricating the pipe that goes to the cat.
But It won't go on!
I noticed there is a split sleeve of tube inside - which i presume is to seal the end where the bolt is - but it all seem s very tight & also close to the swinging arm.
Help appreciated on how you got yours to fit?
I installed mine on a Speed so I'm not sure how much different the fitment is on the scrambler. I removed the split ring sleeve and it has a nice tight fit on the stock cat pipe with no leakage when tightened down. There is adequate clearance between the AEW can and the swingarm on my bike.
Hi
Thank you for the,quick reply.
Fit is same on both bikes.
I checked with my vernier, callers and figured out that the,split tube insert would need removal. But wanted to check....
Have you find the silencer sits very close to the,swinging arm?
Did you have to bend the support bracket over a bit?
Thank you for the,quick reply.
Fit is same on both bikes.
I checked with my vernier, callers and figured out that the,split tube insert would need removal. But wanted to check....
Have you find the silencer sits very close to the,swinging arm?
Did you have to bend the support bracket over a bit?
Joined
·
432 Posts
I found on the scrambler when the swingarm was fully compressed there was a small interference between the exhaust and the swingarm. this may not apply to the street.
No modification necessary on the Speed. I have about 1/2-3/4 inch clearance between silencer and swingarm
If you want something similar, check out British Customs slip on slash tip exhaust, it adds an end bit on but looks very similar to what you have there.
Those wheels looks fantastic.
Hey I took mine off about 500 km ago. No problems. Sounds good when gunning it and think the cat gives it some back pressure if it's needed. I added about 2" of pipe to mine just to get it flush with the heat shield
Hi
Help!
The Aew silencer now fitted actually touches the swinging arm , it has actually marked the back of the silencer. Oldgoldie, how did you increase the clearance? I cannot use the bike as I am concerned more damage will occur to the swinging arm.
The silencer cannot be moved over as the existing mounts on the cat dont allow it!
I have written to the manufacturer and supplier. My bike is a March 24 uk bike.
Help!
The Aew silencer now fitted actually touches the swinging arm , it has actually marked the back of the silencer. Oldgoldie, how did you increase the clearance? I cannot use the bike as I am concerned more damage will occur to the swinging arm.
The silencer cannot be moved over as the existing mounts on the cat dont allow it!
I have written to the manufacturer and supplier. My bike is a March 24 uk bike.
Joined
·
432 Posts
Bad news. I didn't, the silencer is now sitting on a pile of junk.
81 - 100 of 186 Posts
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
